Help!!! After mods, bike wont start??

Thread Tools
 
Search this Thread
 
  #11  
Old 04-14-2009, 06:02 AM
niven's Avatar
Banned
1st Gear Member
Join Date: Mar 2007
Location:
Posts: 282
Default

Fouled plug by the sounds of it. All this new platinum ,mechscrewium dont mean crap, just like yer weedeater change the plug fresh gas and there ya go.
 
  #12  
Old 04-14-2009, 06:52 AM
niven's Avatar
Banned
1st Gear Member
Join Date: Mar 2007
Location:
Posts: 282
Default

Hopefully, ya got air/fuel /compression at the proper time/ after 50 years of bull****.Try a new plug.
 
  #13  
Old 04-14-2009, 07:17 AM
niven's Avatar
Banned
1st Gear Member
Join Date: Mar 2007
Location:
Posts: 282
Default run

Originally Posted by SlapDrum
Yup. All these are good.
My check list is Fuel, Air, and Spark. These three should make it go.
Missing compression my man, fuel,air spark,good bbq.No worries
 
  #14  
Old 04-14-2009, 07:27 AM
BP88's Avatar
Senior Member
1st Gear Member
Join Date: Jun 2008
Location: Westminster, CA
Posts: 359
Default

Originally Posted by niven
Missing compression my man, fuel,air spark,good bbq.No worries
Right, but what has the OP done to his bike to mess with his bike's compression?
 
  #15  
Old 04-14-2009, 07:49 AM
niven's Avatar
Banned
1st Gear Member
Join Date: Mar 2007
Location:
Posts: 282
Default

fuel air compression/ timing
 
  #16  
Old 04-14-2009, 07:51 AM
niven's Avatar
Banned
1st Gear Member
Join Date: Mar 2007
Location:
Posts: 282
Default

If no comp your a wet fart
 
  #17  
Old 04-14-2009, 08:06 AM
niven's Avatar
Banned
1st Gear Member
Join Date: Mar 2007
Location:
Posts: 282
Default

go back to basics . you need intake /exhuast. don't be poring raw gas on rare steak. God only knows, ets help him. missing compression and why I have seen people line up ring end gaps on major thust faces and wonder why oil is blowing out the *** end
 
  #18  
Old 04-14-2009, 08:19 AM
niven's Avatar
Banned
1st Gear Member
Join Date: Mar 2007
Location:
Posts: 282
Default

Brendan.c check out rmdra.ca
 
  #19  
Old 04-15-2009, 02:32 AM
IQOUTLAW's Avatar
Member
1st Gear Member
Thread Starter
Join Date: Oct 2008
Posts: 66
Default

So today after work I got back on it! I tried checking everything listed. I didnt make any mods or do anything to mess with my timing, so that should all be fine.

I started by checking the spark, I pulled the old plug and replaced it with a fresh one, held it against some metal and I do have spark.

I removed my new air filter and checked to make sure I had nothing behind it blocking the intake and as I suspected, it was clear.

I then checked all fuel lines coming from new tank. All lines looked and felt good but to be sure, I unplugged the line from the bottom of the on/off/res. valve and then opened it, fuel went everywhere. SO all lines are free flowing.

I then drained the fuel out of my tank and put about a gallon of fresh gas in. STILL NO LUCK STARTING!!!

I removed th eexhaust and checked to make sure nothing was blocking that, all clear.

I then tried unplugging the new headlight thinking it may be drawing too much power. Still nothing.

After trying and trying and tryign and th ebike just cranking and cran king, I finally got somethign. The bike backfired!!!

THAT WAS THE EXTENT OF IT!!! MY BIKE STILL WONT START!!!

ANYTHING????????????

Thanks, MAXX
 
  #20  
Old 04-15-2009, 05:16 AM
c_m_shooter's Avatar
Senior Member
1st Gear Member
Join Date: Jan 2009
Posts: 151
Default

Give the air cleaner a shot of starting fluid. If it starts for a few seconds and then dies, it means you let it sit too long and will need to clean the carb jets.
 


Quick Reply: Help!!! After mods, bike wont start??



All times are GMT. The time now is 03:59 AM.